Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
In this article down the page you will find more exceptional expertise relating to How to Install a Bathtub.
Setting up a bath tub isn't precisely brain surgery, however it does require solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately tough task. If the old bathtub is easily easily accessible, the job can move quickly; if you have to open up a wall surface to eliminate the old tub and also place the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the new one. Make sure you have actually qualified yourself for the task and fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is far better to think about using one before you begin. Possibilities are you may require a professional plumber to make tube links.
This article will assist you install a brand-new tub in your restroom if you have already acquired a brand-new tub and don't need to alter the plan of your previous water supply pipes.
Your tools and material checklist should comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome due to the limited gain access to that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washers remain in place in between the faucet as well as the sink. Secure the tap in place with the maker offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind ought to be connected to the faucet ends first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Using the two wood boards under its feet, position the bath tub in the required position. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the spirit level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Switch on the water supply and also inspect all joints and also new pipework for leakages and also tighten them if needed. Fill up the bathtub as well as additionally examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, repair the bath paneling as defined in the producer's instruction manual. Tiling as well as securing around the bathtub must wait until the bath tub has been made use of at least when as this will resolve it right into its final placement.
Getting ready for the Installment
First of all, the supporting structure supplied with the bath needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last position.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface between the bath and the tiling, causing issues with wetness and also possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are sold in tubes and cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to permit the motion experienced when the tub remains in use. The sealant can fracture fairly early if you do not take into account this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very fascinated by Tools You Need to Install a New Bathtub and I am assuming you liked our blog entry. Feel free to take the time to promote this blog posting if you liked it. Thank you for taking the time to read it.
Plumbing emergency? We're ready. Report this page